Soller Composites,LLC

820 Epoxy Info

We sell only the very best epoxy!

After reviewing & testing all leading epoxies, we found 820 epoxy to be the best. This is why we are proud to sell this outstanding product!

We will continue to sell West System Epoxy (see below)

 

Summary:

- UV stable (all hardeners)

- Room temp & high temp cure (handles temp up to 210F)

- Post curing compatible

- Very high tensile (breaking strength)

- Low Viscosity (thinner epoxy)

- Available in Qt, Gal, 5Gal, & 55Gal drums

- Very low to no odor

- a professional epoxy that works exceptionally well for pros and hobbyists alike

 

The 820 Epoxy Laminating Systems are developed for the fabrication and repair of high performance composite structures. They consist of one resin and a selection of three separate hardeners to suit your building or repair needs. The resin and hardener combinations produce low viscosity mixtures with convenient volumetric mix ratios. In addition, the 820 Epoxy Laminating Systems are specially formulated for standard wet lay-up or resin-infusion operations requiring the highest degree of fabric wetting and air release attributes. The systems are specifically engineered to promote a high fiber-to-resin ratio and a greater interface with composite fabric(s), thereby resulting in lighter, stronger parts offering lower maintenance and long-term performance.

 

820 Epoxy Laminating Systems are UV stabilized, ultra low viscosity laminating system that is ideal for use in vacuum infusion processes or RTM applications. Use with Graphite, S-Glass, E-Glass or Kevlar fabrics. Produces strong, light weight composite parts. They are specially formulated for standard wet lay-up or resin-infusion operations requiring the highest degree of fabric wetting and air release attributes.

 

We recommend curing 820 & our Nanotube Enhanced Resin between 85F and 160F. We have not tested above 200F and temp below 80F are not recommended due to very long cure times. The 820 and our nano resin will get thick when they get cold. If stored below 60F it may become semi-solid (this does not hurt the resin); if this occurs, put the can in front of a space heater and the resin will become thin and clear again. If you need a resin to cure below 77F, we recommend you consider West Systems below.

 

Mixing Ratio

(100 to 18) Resin to Hardener by weight

(100 to 20) Resin to Hardener by volume

 

     820 Hrdnrs   Pot Life @ 77F   Complete Cure  UV Stable         Dry         Sanding

 

         822         25-30min                7 Days           Yes            ~4-6hrs*       24hrs

         823         40-45min                7 Days           Yes            ~6-8hrs*       24hrs

        824         50-60min                7 Days           Yes            ~12hrs*        24hrs

 

Click here for MSDS info

*****Please note - if you order the pumps, they are a 1 to 1 Ratio*****

We generally recommend you confirm the correct ratio with a scale, even if you use the pumps.

820 Epoxy Pint Kit

Pint Epoxy + 0.2Pint Hardener

UV Stable, 210F, Room Temp or Post Cure, Clear

Resin & Hardener Pumps

 

820 Epoxy Qt Kit

Quart Epoxy + 0.2Qt Hardener

UV Stable, 210F, Room Temp or Post Cure, Clear

Resin & Hardener Pumps

 

820 Epoxy Gal Kit

Gal Epoxy + 0.2Gal Hardener

UV Stable, 210F, Room Temp or Post Cure, Clear

Resin & Hardener Pumps

 

820 Epoxy 5 Gal Kit

5 Gal Epoxy + 1Gal Hardener

UV Stable, 210F, Room Temp or Post Cure, Clear

Resin & Hardener Pumps

 

820 Epoxy 55 Gal Drum Kit

55 Gal Epoxy Drum Kit

UV Stable, 210F, Room Temp or Post Cure, Clear

Resin & Hardener Pumps

******Please contact us for pricing*******

820 Epoxy Pump Kit

Fits Pint, Quart,& Gal Kits

Pump Kit Set   Qty: $14.99

West System Epoxy Kits

West System is a general purpose laminating epoxy that works well for composite laminating. West system's hardeners are thicker than Adtech's above, and are

sometimes adventagous when trying to build-up layers or top coats. West System's 207 hardener is UV stable.

Max temp (HDT)  116F-142F

207 Hardener (only) is UV Stable

Viscosity (cps) 650-975

West Systems Epoxy Quart Kit

West Systems Quart Kits

Epoxy + Hardener + Pump Kit

Note: only 207 Hardener is UV Stable

Room Temp Cure

 

West Systems Epoxy Gallon Kit

West Systems Gallon Kits

Epoxy + Hardener + Pump Kit

Note: 207 Hardener is UV Stable

Room Temp Cure

 

West Epoxy Pump Kit

Fits Pint, Quart,& Gal Kits

Pump Kit Set   Qty: $14.99

5 Min Epoxy Kit (4oz Hardener & 4oz. Resin)

Qty: $17.79

5 Min Epoxy Kit (16oz Hardener & 16oz. Resin)

Qty: $39.49

Epoxy Fillers

403 Microfibers are made of fine cotton fibers and is used as a thickening additive with resin/hardener to create a multi-purpose adhesive. Microfibers and epoxy are particularly effective in bonding wood. Epoxy thickened with microfibers provides good gap-filling qualities while retaining excellent wetting and penetration capabilities. Microfibers are used primarily in bonding and gap-filling applications. Microfibers are non-toxic, but care should be taken to avoid inhalation. Color: Off-White.

 

6oz. $9.99

20oz. $22.99

20lbs. $199.99

 404 High-Density filler is a thickening additive developed for maximum physical properties in hardware bonding where high-cyclic loads are anticipated. It can also be used for filleting and gap-filling where maximum strength is necessary. May be added to the resin/hardener at a rate of 20 to 30% by weight, depending on the viscosity needed. Color: Off-White.

 

 

15.2oz. $13.99

43oz. $29.99

30lbs. $199.99

 405 Filleting Blend is a strong, wood-toned filler for use in glue joints and fillets on naturally-finished wooden interiors. Mixes easily with epoxy and lets you create fillets that are smooth and require little sanding. Color is a consistent tan so it can be used to modify the shade of other West System fillers.

8oz. $15.99

 406 Colloidal Silica is a thickening additive used to control the viscosity of epoxy and prevent epoxy runoff in vertical and overhead joints. 406 is a very strong filler that creates a smooth mixture, ideal for general bonding and filleting. It is also our most versatile filler. Often used in combination with other fillers, it can be used to improve the improve strength, abrasion resistance, and consistency of fairing compounds, resulting in a tougher, smoother surface. Color: off-white.

1.7oz. $9.99

5.5oz. $22.99

10 lbs. $234.99

 407 Low-Density filler is a blended Microballoon-based filler used primarily to make inexpensive filling and fairing putties which are easy to sand or carve while still being a reasonably good engineering material on a strength-to-weight basis. It can also be used as a thickening additive for bonding veneers and in low-stress structural applications where light weight can be beneficial. Good feathering and won't sag. Color: Reddish-Brown.

4oz. $12.99

12oz. $33.75

14 lbs. $335.00

 410 The ideal low-density filler for creating a light, easily worked fairing compound especially suited for fairing large areas. 410 MICROLIGHT handles well and mixes with greater ease than 407 or Microballoons, and is approximately 30% easier to sand. It is also more economical for large fairing jobs but is not recommended under dark paint or other surfaces subjected to high temperatures. Cures to a light tan color. Do not mix 410 MICROLIGHT filler with polyester or vinylester resins. Microlight will inhibit the cure of polyester or vinylester resins.

2oz. $9.92

5oz. $22.15

4 lbs. $199.99

Please Use Epoxy Safely!  Make sure you have protective clothing, gloves, an appropriate respirator and use the product in a well ventilated area.  Please, read the safety info. in the links above and follow all manufacturer's suggestions!

 

Soller Composites assumes no responsibility for the use, misuse, and/or results of the either, of any materials, product, information, and/or suggestions. Customers are strongly encouraged to, and  should/must, research the proper safe use of all products and determine the proper use and suitability of each product for his or her individual application(s).  Soller Composites sole responsibility and/or liability is limited to the replacement of product or refund of the purchase price.  Please contact us if you have any questions.